Steel Thread Cutting Screw, Black Oxide Finish, 82 Degree Flat Undercut Head, Phillips Drive, Type F, #10-32 Thread Size, 3/8″ Length (Pack of 100)
- Steel is often used in applications where strength is the primary consideration. Flat undercut head has a flat top with an 82-degree cone-shaped bearing surface and is undercut for use in shallow countersunk holes. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. Black oxide finish offers mild corrosion resistance and lubricity. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic.
Steel Thread Cutting Screw, Green Zinc Plated, Hex Washer Head, Phillips Drive, Type F, #10-32 Thread Size, 1/2″ Length (Pack of 50)
- Hex washer head has a nonserrated flange for additional grip with the mating surface. Steel is often used in applications where strength is the primary consideration. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. Zinc plating resists corrosion and has a green reflective appearance.
Steel Thread Cutting Screw, Black Zinc Plated, Truss Head, Phillips Drive, Type F, #8-32 Thread Size, 5/8″ Length (Pack of 50)
- Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. Zinc plating resists corrosion and has a black reflective appearance. Steel is often used in applications where strength is the primary consideration. Truss head has an extra-wide low-profile domed shape for applications with minimal clearance.
245 Pc. Thread Cutting Nuts & Push On Retainer Assortment
- Heavier than white tape with density of 135-150 grams/cubic centimeter 4 mils thick. Protection helps make sharp clean threads while extending the life of your dies. Light cutting oil, weatherproof light oil for thread cutting machines. Manufactured especially for natural gas, propane, butane, water, oil and chemical lines. Anti-mist and non-staining formula is not affected by weather. Light cutting oil formulated for hand thread cutting machines. Complies with mil-t-22230a (asg), ul 31 ro, aga 3226 and can/ulc-s642.
Robert Sorby #89HS10 Thread Cutting Set – 10TPI
- Pan head has a flat top and short vertical sides with a rounded top edge. Thread cutting screw with type 23 point style has fine threads that taper down to a blunt point with a large cutting surface suitable for soft metal, provides excellent chip clearance, and requires minimal rotating force to install. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. Steel is often used in applications where strength is the primary consideration. Black oxide finish offers mild corrosion resistance and lubricity.
Steel Thread Cutting Screw, Zinc Plated Finish, Hex Washer Head, Slotted Drive, Type F, 5/16″-18 Thread Size, 1-1/4″ Length (Pack of 10)
- Slotted drive has a linear slot for use with a flat-blade driver. Hex washer head has a flange for additional grip with the mating surface. Steel is often used in applications where strength is the primary consideration. Zinc plating resists corrosion and has a reflective appearance. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic.
Hard-to-Find Fastener 014973311063 Star Drive Thread Cutting, 1/4-20 x 2-Inch, 45-Piece
- Not all fasteners are applicable for all applications so be certain to test thoroughly and get the opinion of a licensed building or certified building or structural engineer before relying on these fasteners for any situations where failure would result in damage to property or person. Most of our fasteners have a light zinc plating over steel giving a more rust resistant finish. We also sell coated and stainless products for additional rust resistance. We stock many grades of fasteners ranging from low carbon steel on up to hardened, heat treated steel. We stock a wide variety of fasteners ideal for many applications around the home, farm, business, automotive, and in industry.
Steel Thread Cutting Screw, Zinc Plated Finish, Hex Washer Head, Slotted Drive, Type F, 5/16″-18 Thread Size, 1″ Length (Pack of 25)
- Hex washer head has a flange for additional grip with the mating surface. Zinc plating resists corrosion and has a reflective appearance. Steel is often used in applications where strength is the primary consideration. Slotted drive has a linear slot for use with a flat-blade driver. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic.
Steel Thread Cutting Screw, Black Oxide Finish, 82 Degree Flat Undercut Head, Phillips Drive, Type F, #6-32 Thread Size, 1/2″ Length (Pack of 100)
- Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic. Black oxide finish offers mild corrosion resistance and lubricity. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. Flat undercut head has a flat top with an 82-degree cone-shaped bearing surface and is undercut for use in shallow countersunk holes. Steel is often used in applications where strength is the primary consideration.
Steel Thread Cutting Screw, Zinc Plated, Hex Head, Type 23, 5/16″-18 Thread Size, 1/2″ Length (Pack of 10)
- Hex head tightens from the side with a wrench, enabling use when there is no space above for a driver. Zinc plating resists corrosion and has a reflective appearance. Steel is often used in applications where strength is the primary consideration. Thread cutting screw with type 23 point style has fine threads that taper down to a blunt point with a large cutting surface suitable for soft metal, provides excellent chip clearance, and requires minimal rotating force to install.
Harvey 016325 1-Gallon Thread Cutting Oil, Dark
- Recent tests show that die cutting with harvey-foots oil run cooler and give sharper threads when compared with five other major brands. Can be used on stainless steel. Used for heavy duty cutting, threading, tapping, and broaching of steel. 1-gallon. A superior quality cutting oil specially formulated to give sharp clean threads and extend die life.
HFS Stainless Steel Screw thread Cutting Angle Gauge Measuring Tool gage
- Stainless steel. Angle scale 29°,30°, 40°, 45°, 50°, 55°, 60°, 65°.
Steel Thread Cutting Screw, Zinc Plated, 82 Degree Flat Head, Phillips Drive, Type F, 5/16″-18 Thread Size, 1″ Length (Pack of 25)
- Zinc plating resists corrosion and has a reflective appearance. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic. Flat head has an 82-degree cone-shaped bearing surface for use in countersunk holes and a flat top that fits flush with the mated surface. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. Steel is often used in applications where strength is the primary consideration.
Steel Thread Cutting Screw, Zinc Plated, Hex Head, Slotted Drive, Type F, #10-32 Thread Size, 1/2″ Length (Pack of 50)
- Steel is often used in applications where strength is the primary consideration. Hex head tightens from the side with a wrench, enabling use when there is no space above for a driver. Zinc plating resists corrosion and has a reflective appearance. Slotted drive has a linear slot for use with a flat-blade driver. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic.
18-8 Stainless Steel Thread Cutting Screw, Plain Finish, 82 Degree Flat Undercut Head, Phillips Drive, Type F, #8-32 Thread Size, 3/4″ Length (Pack of 25)
- Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. Plain surface has no finish or coating. Flat undercut head has a flat top with an 82-degree cone-shaped bearing surface and is undercut for use in shallow countersunk holes. 18-8 stainless steel provides good corrosion resistance and strength. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic.
Steel Thread Cutting Screw, Zinc Plated, 82 Degree Flat Undercut Head, Phillips Drive, Type F, #12-24 Thread Size, 1/2″ Length (Pack of 50)
- Steel is often used in applications where strength is the primary consideration. Flat undercut head has a flat top with an 82-degree cone-shaped bearing surface and is undercut for use in shallow countersunk holes. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening. Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic. Zinc plating resists corrosion and has a reflective appearance.
Wm Harvey 016100 1 Quart Clear Thread Cutting Oil
- Thread cutting oil, specially formulated to give sharp, clean threads and to extend die life. Recent tests show that dies cutting with harvey’s oil run cooler and give sharper threads when compared with other major brands. Use for heavy duty cutting, threading, tapping and broaching of steel. A superior quality cutting oil that can be used on most metals.
Steel Thread Cutting Screw, Zinc Plated, 82 Degree Flat Head, Phillips Drive, Type F, #4-40 Thread Size, 3/8″ Length (Pack of 100)
- Thread cutting screw with type f point has machine screw threads that taper down to a blunt edge and is suitable for heavy gauge sheet metal, aluminum, cast iron, brass, and plastic. Steel is often used in applications where strength is the primary consideration. Flat head has an 82-degree cone-shaped bearing surface for use in countersunk holes and a flat top that fits flush with the mated surface. Zinc plating resists corrosion and has a reflective appearance. Phillips drive has an x-shaped slot that accepts a phillips driver and is designed to prevent over-tightening.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
