Drill America DWDTS Series High-Speed Steel Taper Shank Drill Bit, Black Oxide Finish, 2 Morse Taper Shank, Spiral Flute, 118 Degrees Conventional Point, 5/8″ Size (Pack of 1)
- When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. Designed to perform in a broad range of materials in the iron and steel families. Black oxide treatment adds lubricity and creates small pockets on the surface of the tool that act to hold coolant near the cutting edge. Morse taper shank allows the tool to be inserted directly into the machine’s spindle to facilitate high-torque applications such as large cut diameters. High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance.
2 Morse Taper to 33 Jacobs Taper Drill Chuck Arbor
- For chucks with jacobs taper backs. ) & chuck (jacobs) taper to order the correct arbor. ). Morse taper to jacobs taper arbors have a tang end (not available with a drawbar end. Determine both shank size (to fit into your drill press,tailstock, etc. .
LFA / Reichel Hardware 2MT5/8 2 Morse Taper by 5/8-18 Threaded Arbor, Chrome
- Material is high grade steel and 100% hardened for long life. Ground on centers to give the most accuracy between the drill chuck and machine tool. Press fit jacobs taper, to ensure a non slip fit with drill chuck. Made in france. Guaranteed to run true and balanced. Morse taper end has tang to prevent slippage.
Drill America DEWES4-2 Qualtech Extension Socket, #2 Morse Taper Shank, 4-2 Size (Pack of 1)
- #2 morse taper shank. 4 hole size. . Drill america qualtech extension socket.
Drill America DEWA0206 Qualtech Drill Chuck Arbor, #2 Morse Taper Shank To #6 Jacobs Taper (Pack of 1)
- . Drill america qualtech drill chuck arbor. #2 morse taper shank to #6 jacobs taper.
Chicago Latrobe 110 High-Speed Steel Taper Shank Drill Bit, Black Oxide Finish, #2 Morse Taper Shank, 118 Degree Conventional Point, 5/8″ Size
- Taper shank made to american national standard (morse) dimensions for use in corresponding morse taper holders. Manufactured from premium high-speed steel. General-purpose geometry for drilling in a wide range of operating conditions and materials. Black oxide finish for increased wear resistance and added lubricity standard from stock.
2 Morse Taper to 3/8″-24 Threaded Drill Chuck Arbor
- . Allows you to use a drill chuck with 3/8″-24 threaded back in morse taper of a drill press, mill, lathe tailstock, etc.
Jacobs Chuck 30485 #1 and #2 Morse Taper Ejecting Drift
- Hardened and tempered. Eject morse taper sizes 1 and 2 from sleeves, sockets and machine spindles. Jacobs chuck morse taper ejecting drift.
Jacobs 7308 AO203 Arbor Adapts No.2 Morse Taper to No.3 Jacobs Taper
- Precision machined and ground to master gages for maximum performance with jacobs drill and tap chucks. Ideal for use with custom tool and work holder designs and for specialized machining applications. Adapt jacobs taper to morse tapers, straight shanks, threaded shanks and bridgeport tapers.
Michigan Drill 203 Series High-Speed Steel General Purpose Drill Bit, #2 Morse Taper Shank, Spiral Flute, 118 Degrees Conventional Point, 13/16″ Size (Pack of 1)
- High-speed steel tools are good for most general purpose applications, offering a combination of hardness and toughness for wear resistance. 13/16-inches size. Morse taper shank allows the tool to be inserted directly into the machine’s spindle to facilitate high-torque applications such as large cut diameters. When run in a counterclockwise direction (right-hand cut) spiral fluted tools evacuate chips up and out of the cut to reduce clogging. 118 degrees conventional point.
Alvord Polk 625-0 High-Speed Steel Bridge Reamer, Straight Flute, #2 Morse Taper Shank, Uncoated Finish, Size 5/8 Inch
- Straight flute reamers are recommended for general purpose reaming to make minor enlargements to existing holes with a very precise size and roundness. The end of morse taper shank tools (held in a toolholder) is tapered to ensure accurate alignment of the tool in its socket and is self-holding (friction between the tool and the tool-holder prevents slippage). Uncoated (bright) tools have no finish or coating they are a good choice for general purpose applications. Straight flute reamers are good for use in through or blind holes without interruptions such as keyways (through holes extend through the entire workpiece, while blind holes do not). High-speed steel is a common general purpose steel for cutting tools, is compatible with a variety of materials, and tends to be lower in price than cobalt steel or carbide.
2 Morse Taper to 3 Jacobs Taper Drill Chuck Arbor
- ) & Chuck (jacobs) taper to order the correct arbor. For chucks with jacobs taper backs. . Determine both shank size (to fit into your drill press,tailstock, etc. Morse taper to jacobs taper arbors have a tang end (not available with a drawbar end. ).
2 Morse Taper to 6 Jacobs Taper Drill Chuck Arbor
- ) & Chuck (jacobs) taper to order the correct arbor. ). Determine both shank size (to fit into your drill press,tailstock, etc. Morse taper to jacobs taper arbors have a tang end (not available with a drawbar end. For chucks with jacobs taper backs.
#2 Morse taper
- Outside (shank) 1 morse taper. Soft with hardened tang. Inside (hole) 2 morse taper. Allows the use of a larger morse taper tool. Overall length 6 1/4″.
#2 Morse Taper Collet 7 Pc . Set 1/8″ – 1/2″ 2MT MT2 3/16 1/4 3/8 Round Chuck
- Our part # all-41300. 3/8″-16 threaded back for drawbar. Hardened and precision ground to close tolerance. 7 pcs #2 morse taper shank collets includes 1/8″, 3/16″, 1/4″, 5/16″, 3/8″, 7/16″, & 1/2″. Made of high grade tool steel and comes new in factory packaging.
SODIAL(R) 112mm Length MT3 Spindle to MT2 Arbor Morse Taper Adapter for Lathe
- Only authorized seller of sodial can sell under sodial listings. Drill sleeves is used to change the taper of the connective arbors. Sodial(r) 112mm length mt3 spindle to mt2 arbor morse taper adapter for lathemorse taper 3# to morse taper 2#. Sodial is a registered trademark. The measurement allowed error is 1¡À cm. Notelight shooting and differnent displays may cause the color of the item in the picture a little different from the real thing. The morse taper sleeve is mainly used in drilling machine and lathe machine. . Our products will enhance your experience to unparalleled inspiration. Morse taper shank allows the tool to be inserted directly into the machine’s spindle to facilitate high-torque applications such as large cut diameters.
LFA / Reichel Hardware 2MT6 2 Morse Taper by J6 Arbor, Chrome
- Press fit jacobs taper, to ensure a non slip fit with drill chuck. Guaranteed to run true and balanced. Morse taper end has tang to prevent slippage. . Made in france. Material is high grade steel and 100% hardened for long life. Ground on centers to give the most accuracy between the drill chuck and machine tool.
LC-21 2 Morse Taper Medium Duty Live Center
- Centers have 60 degree point. Built-in washer to protect bearings from grit and dust. Maximum runout of 0008″. 2 morse taper shank. Made of finest heat treated steel, with case-hardened housing.
Alfa Tools DS1605 Size 2-4 Morse Taper Drill Sleeve
- Drill sleeves, also known as reducing sleeves, or shell sockets, are used to adapt taper shank tools where the drill shank is smaller than the machine spindle hole. .
Jacobs 31408 JK 130-MT2 1.0 to 13.0 Millimeter Capacity High Precision Keyless Chuck with #2 Morse Taper Integrated Shank
- All parts are hardened for maximum accuracy and rigidity. Self-tightening feature for maximum gripping power. For cnc machining centers in drilling, boring, counter-boring and milling operations requiring heavy penetration. Precision tested and certified to 0016-inch tir maximum at half capacity. Integrated shank design provides a unit of greater rigidity and precision.
1/2″ Robert Sorby #STB250 Original Stebcentre #2 Morse Taper
- In time critical production turning, the teeth can be backed off with the point still in place, so the workpeice can be stopped and checked without removing it from the lathe, and finished pieces and blanks can be exchanged by backing off the tail stock, rather than starting and stopping the lathe. . It combines a spring loaded center point with a ring of razor sharp teeth. This offers many advantages. Size refers to drive face diameter. Comes in diameters of 1/2″, 7/8″, and 1-1/4″. Robert sorby. With a light setting this offers safety for the novice turner because the workpiece simply stops revolving should a dig-in occur, rather than causing kick back. This revolutionary spur drive center replaces tradtional spur drives and gives all the great stebcentre advantages. Made in england. By winding in the tail stock the degree of “bite” can be varied while still keeping the center point firmly located.
We are a participant in the Amazon Services LLC Associates Program, an affiliate advertising program designed to provide a means for us to earn fees by linking to Amazon.com and affiliated sites.
